The potatoes were done. The wet July weather caused a few to rot, but the damage was minimal. We will be moving them down to the basement shortly.
Subscribe to:
Post Comments (Atom)
skip to main |
skip to sidebar
McLeansboro, IL
IWB Holsters, P-TAP Trigger Protectors, Extra Magazine Carriers!
Click The Engine For The Link
319 OLDGOLD; JBench(dot)Johnson(at)gmail.com Custom Jewelry, Rocks At Rock Bottom Prices, Really!
Contact Tractor Joe! Click The Pic!
Click on the banner to see the current posts.
Click on the labels at the end of the posts to find related posts.
Click on 'Older Posts' to go to the next page.
Click on the labels at the end of the posts to find related posts.
Click on 'Older Posts' to go to the next page.
Home Life
Larry's, A Great Local Gun Shop
McLeansboro, IL
HAWG Holsters
IWB Holsters, P-TAP Trigger Protectors, Extra Magazine Carriers!
Old Time Farm Toys From Kester's Collectables! Hand Made American Toys For Kids Of All Ages!
Click The Engine For The Link
Blog List: Start Clicking
- Ace Of Spades
- Active Response Training
- Adventures Of Roberta X
- Ammo Land
- Backwoods Home Magazine
- Bayou Renaissance Man
- Bendigo Strange
- Billlls Idle Mind
- Blog O' Stuff
- Blue's Blog
- Borepatch
- Cheaper Than Dirt Blog
- Claire Wolfe, Living Freedom
- Clayton Cramer
- Clayton Cramer: Gun Self Defense
- Common Cents
- Daily Time Waster
- Dead Men Do Bleed, True Blue Sam's Other Blog
- Earl's View
- Eaton Rapids Joe
- Engineering Johnson
- Feral Irishman
- Freedom Is Just Another Word
- Gates of Vienna: Islam's War of Terror
- Gear Expert, Optics Planet Blog and Sales
- Gun Blog Blacklist
- Gun Nuts Media
- GunBloggers.com
- Home On The Range
- In The Middle Of The Right
- Instapundit
- Julie Golob Blog
- KeeWee's Corner
- Michael Bane Blog
- Mr. Completely- Most Excellent Gun Blog
- Mrs. True Blue Sam
- Musings By The Creekside
- Never Yet Melted
- New Jovian Thunderbolt
- Not Clauswitz
- NSSF Blog
- PawPaw's House
- SandCastle Scrolls
- Say Uncle
- Shall Not Be Questioned
- Shooting With Hobie
- Smallest Minority
- Sondra K's Gulch (Formerly Knowledge Is Power)
- Stilton's Place
- Straight Forward In A Crooked World
- The Clue Meter
- The Feral Irishman
- The Firearm Blog
- The Freeholder
- The Stranded Tree Farm
- The Truth About Guns
- The Ultimate Answer To Kings
- The View From North Central Idaho
- Train Wreck In Maxwell
- View From The Porch
- Whisky Reviews by Ralfy
- Women's Outdoor News
Forums, Reference, and Etc.
- American Rifleman
- Box o' Truth
- Drudge Report
- ForestApps (Chainsaw Safety)
- Gun Rights Media
- Gun Values Board
- Gunblast.com
- HandgunLaw.us
- Handloads.com
- Iowa Carry: 99 different policies!
- Learn About Guns
- Lubrication 101, by Grant Cunningham
- Minuteman Review
- National Rifle Association
- Paco Kelly's Leverguns
- Ruger Forum
- Single Action Shooting Society
- SmokStak: Old Engine Forum
- Talking Machine Forum
- True Blue Sam's YouTube channel
- Victor Library
Sexy Diamonds
319 OLDGOLD; JBench(dot)Johnson(at)gmail.com Custom Jewelry, Rocks At Rock Bottom Prices, Really!
Need Phonograph Needles?
Got Tractor? Get The Parts You Need!
Contact Tractor Joe! Click The Pic!
Stoke Up!
- FARM COLLECTOR SHOW DIRECTORY!
- Midwest Central Railroad
- Midwest Old Settlers and Threshers
- Midwest Central Railroad Blog
- Midwest Old Threshers: A Fan Blog
- National Threshers Association
- Pinckneyville Illinois Steam Show
- Pioneer Engineers, Rushville, IN
- Rough and Tumble Engineers Historical Association
- Cumbres and Toltec Railroad
- Durango and Silverton Railroad
- Georgetown Loop Railroad
- 1880 Train
- Mid Continent Railway Museum
- Farm Collector
- Gas Engine Magazine
- Steam Traction Magazine (Formerly Iron Men Album)
- Engineers and Engines Magazine
Resources, Supplies
- AmmoDotCom
- Ammunition To Go!
- Bailey's Logging Supply; Chainsaws, Parts, Safety Gear
- Brownells
- Cabela's
- CHEAP AMMO dot Com!
- Cheaper Than Dirt
- Dixie Gun Works
- D S Welding Steel Targets
- Galati Gear
- Graf and Sons
- Hi-Point Firearms
- Lucky Gunner Ammo
- Magnum Shooters Supply
- Midway USA
- Minuteman Review
- Natchez Shooters Supply
- Optics Planet: Accessories, but located in Cook Co IL; No Mags Over 10 Rounds!
- Rifleman Training Targets
- Ruger
- SG Ammo
- Springfield Armory
- Taylor's Firearms
- Track Of The Wolf
- Tractor Joe; Parts For Your Tractor!
- Widener's Reloading and Shooting Supplies
Click On Labels For Related Articles
- Adventures (28)
- Antiques (454)
- Aviation (34)
- Barns (33)
- Chainsaws (347)
- Close Calls (11)
- Cultural Resources (48)
- Down On The Farm (265)
- E-Postal Match (207)
- Education (51)
- Family (101)
- Fine Art (5)
- Fire (28)
- Flowers (100)
- Forest Products Utilization (85)
- Forestry (325)
- Gas Engines and Tractors (765)
- Gun Blogger Rendezvous (94)
- Heroes (220)
- Holidays (832)
- Humor (125)
- Hunting (35)
- Medical Stuff (35)
- Music (1934)
- News (9)
- Old Publications (50)
- Pets (230)
- Poetry (72)
- Project Valour-IT (19)
- Railroads (534)
- Second Amendment Rights (495)
- Shooting (507)
- Steam (1135)
- Sustenance (105)
- T's And Other Old Vehicles (93)
- Travel (50)
- Trees Do The Darndest Things (18)
- Under The Car (32)
- Violin (17)
- Weather (128)
- gadgets (327)
- history (223)
- wildlife (220)
Blog Archive
-
▼
2025
(435)
-
▼
July
(27)
- More Garden News
- Sixteen Pints!
- Tuesday Torque: Oil City Allis WC!
- Coming Up From The Basement Monday!
- Abandoned Locos....
- Don't Disturb The Roots!
- Weekend Steam: Boonville, IN Summer Show, This We...
- Tinian, The Forgotten Invasion, From The History Guy
- Where Do The Years Go?
- Participation Trophy Winner!
- Tuesday Torque: Oil Creek And Titusville Railroad
- Susan Is Busy!
- Weekend Steam II: Denton, North Carolina
- Weekend Steam: A Couple Of Good Ones!
- Cowboy Boots And Shorts? Not A Hard Hat To Be Seen.
- Tuesday Torque II: Holt Crawler
- Tuesday Torque: Tractor or Automobile?
- Starving Squirrels?
- Triplets!
- Weekend Steam: Antique Mamod Engine.
- The Latest Schips, Bella and Stella
- William Kirk, Washington Gun Law Channel, On Illin...
- Tuesday Torque: 1911 Mack Manhattan
- Weekend Steam: UP 844, 80 mph!
- Fledged Phoebes!
- The Beer Can Burglars Are Back!
- Interview With A Funeral Director/Undertaker
-
▼
July
(27)
Rules To Live By
Firearms; Col. Jeff Cooper's Rules
1. All guns are always loaded.
2. Never let the muzzle cover anything you are not willing to destroy.
3. Keep your finger off the trigger until you are ready to shoot.
4. Be sure of your target and what lies beyond it.
Knives
1. Never cut toward yourself.
2. Always cut away from yourself.
3. Never cut yourself.
AND
If you drop a knife or gun, let it fall!
Chainsaws
1. Always wear your safety gear when running your saw: hard hat, eye, face, hearing protection, cut resistant protection for your legs, heavy boots, gloves (depending on work conditions).
2. Safety devices on the saw must be in working order: front hand guard,chain brake, chain catcher, throttle lockout, and right hand guard.
3. Hold the saw on the ground or lock it between your knees for starting. No 'Drop Starts.' Set the chain brake before cranking.
4. The engine must idle reliably without turning the chain.
5. The chain must be sharpened properly, including properly set depth gauges.
6. The chain must be adjusted to remove slack and still run freely.
7. The operator must understand the forces on different parts of the bar as the saw runs: push, pull, kickback and attack.
8. Both hands must always be on the saw when the chain is running. The thumbs must be wrapped around the handles. Both feet should be firmly planted on the ground.
9. The operator must always know where the end of the bar is, and what it's doing.
10. Don't let the upper (kickback) corner of the bar contact anything when the chain is running unless the tip has been buried with the lower corner.
11. Let off of the throttle before pulling out of a pinch on the top part of the bar.
12. Make a plan for every tree you cut. Assess hazards, lean, escape routes, forward cuts, and back cuts. Evaluate the forward or backward lean, and the side lean of every tree you cut. Know your limits.
1. All guns are always loaded.
2. Never let the muzzle cover anything you are not willing to destroy.
3. Keep your finger off the trigger until you are ready to shoot.
4. Be sure of your target and what lies beyond it.
Knives
1. Never cut toward yourself.
2. Always cut away from yourself.
3. Never cut yourself.
AND
If you drop a knife or gun, let it fall!
Chainsaws
1. Always wear your safety gear when running your saw: hard hat, eye, face, hearing protection, cut resistant protection for your legs, heavy boots, gloves (depending on work conditions).
2. Safety devices on the saw must be in working order: front hand guard,chain brake, chain catcher, throttle lockout, and right hand guard.
3. Hold the saw on the ground or lock it between your knees for starting. No 'Drop Starts.' Set the chain brake before cranking.
4. The engine must idle reliably without turning the chain.
5. The chain must be sharpened properly, including properly set depth gauges.
6. The chain must be adjusted to remove slack and still run freely.
7. The operator must understand the forces on different parts of the bar as the saw runs: push, pull, kickback and attack.
8. Both hands must always be on the saw when the chain is running. The thumbs must be wrapped around the handles. Both feet should be firmly planted on the ground.
9. The operator must always know where the end of the bar is, and what it's doing.
10. Don't let the upper (kickback) corner of the bar contact anything when the chain is running unless the tip has been buried with the lower corner.
11. Let off of the throttle before pulling out of a pinch on the top part of the bar.
12. Make a plan for every tree you cut. Assess hazards, lean, escape routes, forward cuts, and back cuts. Evaluate the forward or backward lean, and the side lean of every tree you cut. Know your limits.
13. Clear your work area and your escape path of brush, vines, and other hazards that can trip you or catch your saw.
14. Escape from the bullseye when the tree tips. 90% of accidents happen within 12 feet of the stump. Go more than 15 feet, and stay out of the bullseye until things stop falling.
15. Keep spectators away more than twice the height of the tree in the direction it will fall.
16. Don't cut alone.
17. Keep your body and the swamper's out of the line of the bar in case of a kickback.
18. Set the brake when taking over two steps or when moving through tripping hazards. Keep your trigger finger off of the throttle when you are moving.
19. DO NOT operate a chainsaw from a ladder! Operating with your feet off the ground requires special training.
20. Do not cut above your shoulders.
21. Springpoles must be shaved on the inside of the apex between the ascending and descending sides. If the apex is higher than you shoulders, stand under the springpole and cut it low on the descending side. It will release upward, away from you.Leaning and heavily loaded poles that are too small to bore cut for a hinge should be shaved on the compressed side until they fold.
22. Do not cut a tree that is holding up a lodged tree. Do not work under a lodged tree. Think about a mouse trying to steal the cheese out of a trap.
23. Instruct your swampers and helpers to NEVER approach you from behind or the sides to within the reach of your saw when you are cutting. If you pull out of a cut with the chain running, or have a severe kickback, the swamper can be killed if he is coming up behind you!
24!! Quit When You Are Tired!25!! Pause and review; reflect, when you are being pushed. You may be pushed into danger. Do not let pressure cause you to ignore safety rules!
Cutting dead and rotten trees is extremely risky, and your safety always comes down to basics and following the rules. Build a good hinge, even if there is just a thin shell to work with. Support the back side of the hinge with wedges if the tree is punky or hollow before you cut out the back. Don't fight side lean or back lean when cutting unsound trees. Release it quickly and get away from the stump. Tell your co-workers what your steps are before you crank your saw. You will live long.
Drop That Tree Where You Want It!
Blog Themesong!
FTC Required Disclosure
The FTC now requires disclosure of the relationships between bloggers and the products, services, and companies which they discuss or advertise.
The blog known as "True Blue Sam the Travelin' Man" (hereafter known as The Blog) is a recreational publication and not a commercial entity. The Blog's authors and contributors receive no income, discounts, products, gratuities, or other payment from any of the businesses, individuals, and other entities which are mentioned, discussed, depicted, shown in videos, promoted, or linked on the blog. The authors of The Blog create material (including but not limited to written text, illustration, audio and video) for their own personal enjoyment and the enjoyment or education of those who read The Blog.
Third party advertisements (Over which The Blog has no control.) placed on some of The Blog’s videos and on the sidebar of this blog may provide income to the publishers of “True Blue Sam the Travelin’ Man."
The blog known as "True Blue Sam the Travelin' Man" (hereafter known as The Blog) is a recreational publication and not a commercial entity. The Blog's authors and contributors receive no income, discounts, products, gratuities, or other payment from any of the businesses, individuals, and other entities which are mentioned, discussed, depicted, shown in videos, promoted, or linked on the blog. The authors of The Blog create material (including but not limited to written text, illustration, audio and video) for their own personal enjoyment and the enjoyment or education of those who read The Blog.
Third party advertisements (Over which The Blog has no control.) placed on some of The Blog’s videos and on the sidebar of this blog may provide income to the publishers of “True Blue Sam the Travelin’ Man."
No comments:
Post a Comment